镀锌板的尺寸规格

规格 锌层 材质 0.25*1000*C 80 DX51D+Z 0.25*1000*C 80 DX51D+Z 0.3*1000*C 80 DX51D+Z 0.35*1000*C 80 DX51D+Z 0.4*1000*C 80 DX51D+Z 0.5*1000*C 80 S280GD+Z 0.5*1000*C 80 DX51D+Z 0.58*1000*C 80 S350GD+Z 0.6*1000*C 80 DX51D+Z 0.7*1000*C 80 DX51D+Z 0.75*1000*C 80 DX51D+Z 0.8*1000*C 80 DX51D+Z 0.8*1000*C 80 DX53D+Z 0.85*1000*C 80 DX51D+Z 0.9*1000*C 80 DX51D+Z 0.98*1000*C 80 DX51D+Z 0.95*1000*C 80 DX51D+Z 1.0*1000*C 80 DX51D+Z 1.1*1000*C 80 DX51D+Z 1.2*1000*C 80 DX51D+Z 1.2*1050*C 150 CSB 1.4*1000*C 80 DX51D+Z 规格 锌层 材质 1.5*1000*C 80 DX51D+Z 1.55*1000*C 180 S280GD+Z 1.55*1000*C 180 S350GD+Z 1.6*1000*C 80 DX51D+Z 1.8*1000*C 80 DX51D+Z 1.9*1000*C 80 DX51D+Z 1.95*1000*C 180 S350GD 1.98*1000*C 80 DX51D+Z 1.95*1000*C 180 S320GD+Z 1.95*1000*C 180 S280GD+Z 1.95*1000*C 275 S350GD+Z 2.0*1000*C 80 DX51D+Z 规格 锌层 材质 0.36*1250*C 80 　0.4*1250*C 80 DX51D+Z 0.42*1250*C 80 DX51D+Z 0.45*1250*C 225 S280GD+Z 0.47*1250*C 225 S280GD+Z 0.5*1250*C 80 SGCC 0.55*1250*C 180 S280GD+Z 0.55*1250*C 225 S280GD+Z 0.6*1250*C 80 DX51D+Z 0.65*1250*C 180 DX51D+Z 0.7*1250*C 80 DX51D+Z 0.7*1250*C 80 SGCC 0.75*1250*C 80 DX51D+Z 0.8*1250*C 80 DX51D+Z 0.9*1250*C 80 DX51D+Z 0.95*1250*C 80 DX51D+Z 规格 锌层 材质 1.0*1250*C 80 DX51D+Z 1.15*1250*C 80 DX51D+Z 1.1*1250*C 80 DX51D+Z 1.2*1250*C 80 DX51D+Z 1.35*1250*C 80 DX51D+Z 1.4*1250*C 80 DX51D+Z 1.5*1250*C 80 DX51D+Z 1.55*1250*C 80 DX51D+Z 1.6*1250*C 120 SGCC 1.6*1250*C 80 DX51D+Z 1.8*1250*C 80 DX51D+Z 1.85*1250*C 90 DX51D+Z 1.95*1250*C 80 DX51D+Z 1.75*1250*C 80 DX51D+Z 2.0*1250*C 80 DX51D+Z 2.0*1250*C 120 SGCC 2.5*1250*C 80 DX51D+Z 有关产品标准都列明镀锌板推荐的标准厚度、长度和宽度及其允许偏差。一般来说，镀锌板越厚允许误差越大，而不是固定的0.02-0.04毫米，厚度偏差还根据屈服度、拉伸系数等不同而有不同要求，长宽偏差一般在5mm ，板材的厚度一般在0.4-3.2之间 。